DO NOT TURN WATER OFF UNTIL IT REACHES THE MIDDLE OF THE SKIMMER. IT COULD LEAVE A WATER RING. IF NOT FILLED BY NIGHTIME, THEN LOWER THE WATER PRESSURE UNTIL MORNING.

  NOTICE  A STAIN OR THE LIGHT DOES NOT COME ON, KEEP FILLING THE POOL AND WE CAN FIX WHEN THE POOL IS FULL OF WATER. 

   NOTIFY US IF YOU HAVE A NON TITANIUM HEATER.  WE NEED TO BYPASS IT BEFORE ANY CHEMICALS ARE ADDED TO THE POOL.

   DO NOT RUN POOL HEATERS FOR ONE MONTH.  SOLAR IS OK.

   NO CHLORINE OR STABILIZER UNTIL FIFTH DAY - AND-  ALL MINERALS (IRON, COPPER) ARE REMOVED FROM THE WATER.

   SALT GENERATORS DO NOT USE ANY SALT FOR ONE MONTH.  USE CHLORINE TABS AND LIQUID CHLORINE FOR THE FIRST MONTH.

   DO NOT VACUUM POOL FOR TWO WEEKS.

   YES BRUSH POOL DAILY FOR TWO WEEKS AND KEEP PH LOW.

   SWIMMING: LOWER LEVELS OF PH FOR THE FIRST TWO WEEKS MAY IRRITATE SENSITIVE SKIN OR BURN EYES.  USE YOUR OWN JUDGEMENT PLEASE. 

DAY 1

1 .WHEN POOL IS FULL, MAKE SURE ANY CAPS OR PLUGS THAT MAY OF BEEN REMOVED, ARE REPLACED AND ON SECURELY. TURN PUMP ON.  IF THE PUMP DOESN'T WANT TO REACH A FULL HEAD, TURN IT OFF AND OPEN UP THE BASKET LID AND LET A WATER HOSE RUN IN THERE FOR 2 MINUTES. REPLACE BASKET LID AND TURN PUMP ON AGAIN. RUN POOL FOR 24 HOURS A DAY FOR THE FIRST 5-7 DAYS.

2. ADD 3 GALLONS OF ACID AND BRUSH POOL.  USE EXTREME CAUTION WHEN HANDLING ACID.  ALWAYS MIX ACID TO A BUCKET FULL OF WATER, THEN ADD TO THE DEEP END OF THE POOL. ADDING ACID LOWERS THE PH AND ALKALINITY LEVELS.  FOR TWO WEEKS ONLY RECORD YOUR PH LEVELS AND MAKE SURE THE PH DOES NOT RISE ABOVE 7.2. EVERY 2 TO 3 DAYS AS THE PH RISES UP TO 7.2 YOU WILL NEED TO ADD 1 GALLON OF ACID.    ALKALINITY WILL GET ADJUSTED STARTING ON DAY 15.

3. ADD I QUART OF A SEQUESTERING AGENT /  METAL CONTROL SOLUTION PER 10,000 GALLONS OF WATER. THIS SOLUTION WILL HELP PREVENT STAINING ON THE POOL FINISH . IT WILL KEEP OUT ANY COPPER OR IRON  FROM THE POOL WATER.. A LEVEL 10 - 15 PPM MUST BE MAINTAINED FOR THE LIFE OF THE POOL.  YOU MUST LET YOUR POOL TECH OR POOL STORE KNOW THIS. WARRANTY WILL BE VOID IF THESE LEVELS ARE NOT MAINTAINED.

DAY 2  AND DAY 3

CHECK PH LEVEL.  MAINTAIN A LEVEL BETWEEN 6.5 - 7.2 FOR TWO WEEKS.  WHEN YOU ADD ACID, IT WILL LOWER THE PH BELOW 6.5.  WITHIN 2-3 DAYS THE PH WILL RISE UP TO 7.2 OR HIGHER. WHEN IT GETS UP TO 7.2 YOU MUST ADD 1 GALLON OF ACID.

DAY 4 OR DAY 5

TAKE A WATER SAMPLE TO THE POOL STORE AND MAKE SURE THERE ISN'T ANY MINERALS IN THE WATER. IF METALS ARE PRESENT, YOU MUST PURCHASE MORE SOLUTION TO REMOVE THE MINERALS BEFORE ANY CHLORINE OR STABILIZER IS ADDED.

WHEN ALL THE MINERALS,METALS,IRON ECT. ARE GONE, THEN START THE ADDITION OF:

ADD 2 CHLORINE TABS TO THE CHLORINATOR.. OR THE SKIMMER IF YOU HAVE A SALT GENERATOR....         MAINTAIN A READING OF 1.0 - 2.0 .

ADD STABILIZER TO THE SKIMMER SLOWLY. THE POOL TECH WILL TELL YOU HOW MUCH TO USE. WE RECOMMEND THAT YOUR FILTER BE CLEANED PRIOR TO THE ADDITION OF THE STABILIZER.     MAINTAIN A READING OF 30-80 PPM.

DO NOT SHOCK POOL FOR 3 WEEKS IN SUMMER AND 4 WEEKS IN THE WINTER. 

DAY 6 THRU DAY 14

CHECK PH  (FOLLOW DAY 2 AND 3 STATED ABOVE)..  MAINTAIN A CHLORINE LEVEL 1.0-2.0,  BRUSH POOL DAILY,  CLEAN FILTER AS NEEDED,

DAY 15 THRU DAY 30

1. THE PH LEVEL WILL START TO MAINTAIN A LEVEL. KEEP BETWEEN 7.2-7.6.

2. START THE ADDITION OF ALKALINITY INCREASER  2-3 LBS. AT  A TIME AS NEEDED TO BRING UP TO THE LEVEL OF 80-100 PPM.

3. MAINTAIN  CHLORINE 1.0-2.0

DAY 30

CALCIUM SHOULD BE ADJUSTED  AND MAINTAINED AT .....    180-250 PPM 

NOW ALL CHEMICALS SHOULD BE MAINTAINED AS PER THE POOL STORE. BRUSH POOL ONCE A WEEK. MAINTAIN A SEQESTERING LEVEL UP TO 15 PPM.